Inorganic–organic hybrid materials with zirconium oxoclusters as protective coatings on aluminium alloys

Inorganic–organic hybrid materials are attracting a strong scientific interest mainly for their outstanding inherent mechanical and thermal properties, which can be traced back to the intimate coupling of both inorganic and organic components. By carefully choosing the experimental parameters used for their synthesis, chemically and thermally stable acrylate-based hybrid material embedding the zirconium oxocluster Zr₄O₄(OMc)₁₂, where OMcCH₂C(CH₃)C(O)O, can be deposited as UV-cured films on aluminium alloys.

In particular, the molar ratios between the oxocluster and the monomer, the polymerisation time, the amount of photo-initiator and the deposition conditions, by using an home-made spray-coating equipment, were optimised in order to obtain the best performing layers in terms of transparency and hardness to coat aluminium alloy (AA1050, AA6060 and AA2024) sheets. Furthermore, it was also evaluated whether the hybrid coatings behave as barrier to corrosion.

Several coated samples were prepared and characterised. Environmental scanning electronic microscopy (ESEM) and scratch test were used to investigate the morphology of the films and to evaluate their scratch resistance, respectively. Electrochemical impedance spectroscopy (EIS) was performed in order to evaluate if the coatings actually protect the metallic substrate from corrosion.

In order to measure shear storage modulus (G′) and loss modulus (G″) of the materials used for coatings, bulk samples were also obtained by UV-curing of the precursors solution. Dynamical mechanical thermal analysis (DMTA) was performed in shear mode on cured disks of both the hybrid materials and pristine polymer for comparison. The values of T_g were read off as the temperatures of peak of loss modulus. The length and mass of all the samples were measured before and after the DMTA analysis, so that the shrinkage of the materials in that temperature range was exactly evaluated.     

Method to Characterize the Air Flow and Water Removal Characteristics During Vacuum Dewatering. Part II—Analysis and Characterization

This is part II of a study reported earlier on a method to characterize the air flow and water removal characteristics during vacuum dewatering. This article presents experimental data and analysis of results from the use of a cyclically actuated vacuum dewatering device for removing moisture from wetted porous materials such as paper with the intermittent application of vacuum and accompanying air flow though the material. Results presented include sheet moisture content as a function of residence time and hence water removal rate under a variety of process conditions. Also, experimental results on air flow through the wet porous structure and hence the role and importance of air flow during vacuum dewatering are presented. Vacuum dewatering process conditions include exit solids content between 11 and 20% solid under applied vacuum conditions of 13.5 to 67.7 kPa (4 to 20 in. Hg). Regression analysis indicated that the exit sheet moisture content exhibited a nonlinear relationship with residence time with exit solids reaching a plateau after a certain residence time. Final moisture content correlated linearly with the average overall flow rate of air through the paper sample and the basis weight of the material.     

Effect of Wall Surface Properties at Different Drying Kinetics on the Deposition Problem in Spray Drying

Current methods in alleviating the wall deposition problem in spray drying emphasize mainly controlling the stickiness of the drying particles and less attention is placed on the properties of the dryer wall. In this experimental study, the effect of wall surface properties on the deposition mechanism has been investigated. Properties considered in classifying different wall materials were surface energy, roughness, and dielectric properties. The model solution contained sucrose, representing low-molecular-weight sugars commonly encountered in spray drying of fruit and vegetable juices. The effect of wall properties on deposition was explored at different drying rates producing particles of different surface rigidity. Larger surface roughness produced higher deposition fluxes for particles with high impact velocity and moisture. Surface energy and surface roughness were found to have no significant effect for dry rigid particles at the middle and bottom elevation of the drying chamber. However, material with lower surface energy (Teflon) exhibited less deposition for rubbery particles at such elevations. Analysis shows that dielectric wall material (Teflon) tends to enhance deposition of dry particles because of attrition at the surface. Higher wall temperature was found to produce slightly more deposition. The results of this work give a general indication of the effect of wall material on the deposition problem and provide the fundamental understanding for further studies along this line. Proper selection of dryer wall material will provide potential alternatives for reducing the deposition problem.     

Synthesis of TiO<Subscript>2</Subscript> Hybrid Molecular Imprinted Polymer for Ethofumesate Linked by Silane Coupling Agent

TiO₂ hybrid molecular imprinted polymer (MIP) for ethofumesate using methacrylic acid (MAA) as the functional monomer and silane coupling agent 3-(trimethoxysilyl) propylmethacrylate (KH570) as organic–inorganic connective bridge was synthesized via photo-excitation method. Hydrogen bond was proved to act between MAA and ethofumesate for pre- and post-polymerization binding properties as testified by UV spectrometric method. KH570 modified TiO₂ nanoparticles were prepared via sonochemical reaction, which can accelerate hydrolysis, increase collision chance for the reactive system and improve the dispersion of the nanoparticles. Scanning electron microscope (SEM), transmission electron microscope (TEM), binding and the adsorption kinetics experiments as well as thermogravimetric analysis (TGA) were employed for characterization. The results indicated that the hybrid MIP revealed a larger surface area and more ordered imprinting cavities with improved thermal stability compared to organic-only MIP. Furthermore, faster adsorption kinetics and enhancive adsorption capacity were achieved, which made it promising in chemical sensor applications.     

溶胶凝胶法聚合物/无机复合材料的研究与应用

介绍了制备聚合物/无机复合材料的溶胶凝胶原理,基本过程及制备途径,简要阐述了其在光学材料、电子材料、生物材料、涂层材料、纳米材料等领域的研究及应用进展,指出了其进一步研究的发展方向和重点。     

多孔材料透过性能的表征

透过性能对用于过滤分离、流体混合、布气分流等方面的多孔材料是一项十分关键的质量指标。主要介绍了多孔材料透过性能的表征方式，包括流体流动的基本概念、层流条件下流体的透过性能表征、多孔材料透过性能的综合表征、气体透过多孔材料时渗透系数的具体表征等方面。     

Al2O3对镁铬耐火材料致密化的影响

为了提高镁铬耐火材料的烧结性能,通过考察气孔率、体积密度和常温耐压强度与Al2O3加入量之间的关系,讨论了Al2O3添加剂对两种不同镁铬耐火材料致密化的影响.结果表明,镁铬耐火材料的骨料不同,Al2O3对其烧结性能和致密化的影响也不一样.